INC-196389 · Issue 690786
ConfigurationReconciliationTask updated for greater compatibility
Resolved in Pega Version 8.7
After updating from Pega 8.3 to Pega 8.6, models which previously had learning and performance AUC greater than 0.7 reported an AUC of 0.5. This was traced to the update handling in ConfigurationReconciliationTask. AdmRuleBrowser does not perform ruleset resolution, so all rules were returned, for example the rule for model A in both the 08-01 and 08-03 ruleset. The system then iterated over all of the adaptive model rules returned by AdmRuleBrowser in order to assess whether a configuration update was necessary. The condition to update the model rule was met when either the config key did not exist (indicating a newly added configuration) or the model rule was "old" (version <2). For models generated in Pega 8.3 or earlier the version number for all rules must be 1, and the update to Pega 8.6 therefore caused the ConfigurationReconciliationTask to be applied to all adaptive model rules. To resolve this, the configuration update check in ConfigurationReconciliationTask has been removed.
INC-201335 · Issue 690733
ConfigurationReconciliationTask updated for greater compatibility
Resolved in Pega Version 8.7
After updating from Pega 8.3 to Pega 8.6, models which previously had learning and performance AUC greater than 0.7 reported an AUC of 0.5. This was traced to the update handling in ConfigurationReconciliationTask. AdmRuleBrowser does not perform ruleset resolution, so all rules were returned, for example the rule for model A in both the 08-01 and 08-03 ruleset. The system then iterated over all of the adaptive model rules returned by AdmRuleBrowser in order to assess whether a configuration update was necessary. The condition to update the model rule was met when either the config key did not exist (indicating a newly added configuration) or the model rule was "old" (version <2). For models generated in Pega 8.3 or earlier the version number for all rules must be 1, and the update to Pega 8.6 therefore caused the ConfigurationReconciliationTask to be applied to all adaptive model rules. To resolve this, the configuration update check in ConfigurationReconciliationTask has been removed.
SR-D66223 · Issue 529994
Update Handler will not run during migration
Resolved in Pega Version 8.3.2
Rolling restart of DataFlow, ADM ,VBD, and Util Tiers failed with a PENDING_JOINING error after an in-place upgrade. This was traced to the logic for the update timing: when nodes start after an upgrade from 7.x to 8.x they will migrate data flow runs. Migration happens on only one node, and while it's in progress the other nodes will wait until migration finishes before they come up. At this point the state of the data flow services will be 'PENDING JOINING'. The issue is that while migrating runs, the Data Flow Update Handler was triggered to validate whether there were nodes available on the service the run belongs to. This call can cause the corresponding data flow service to be initialized, but the call will be blocked since all services wait for the migration to end. This resulted in a deadlock which prevented all nodes from coming up successfully. To resolve this, the process has been updated to skip the update handler during migration to avoid triggering the initialization of client services that are waiting on the migration lock.
SR-D68707 · Issue 529869
Update Handler will not run during migration
Resolved in Pega Version 8.3.2
Rolling restart of DataFlow, ADM ,VBD, and Util Tiers failed with a PENDING_JOINING error after an in-place upgrade. This was traced to the logic for the update timing: when nodes start after an upgrade from 7.x to 8.x they will migrate data flow runs. Migration happens on only one node, and while it's in progress the other nodes will wait until migration finishes before they come up. At this point the state of the data flow services will be 'PENDING JOINING'. The issue is that while migrating runs, the Data Flow Update Handler was triggered to validate whether there were nodes available on the service the run belongs to. This call can cause the corresponding data flow service to be initialized, but the call will be blocked since all services wait for the migration to end. This resulted in a deadlock which prevented all nodes from coming up successfully. To resolve this, the process has been updated to skip the update handler during migration to avoid triggering the initialization of client services that are waiting on the migration lock.